AC Coupled battery - Atmoce 7kWh M-Battery
CEC approved

- Configurable for 1ph or 3ph installations
- Programmable kVA output with options for 1.65/2.5/3.0/3.68/3.84kVA
- Requires IQ system controller for backup solutions
- Enphase CK2 kit can be used for grid connected battery storage without backup
- Wall 

SKU: 120020-94700 

sonnenBatterie sBEvo
Ethernet internet connection only per sonnen warranty - Wifi not supported

Kit includes:
- Carton 1 - 3000286 outdoor rated enclosure, inverter and plinth
- Carton 2 - 3000292 accessory kit (energy meter, CTs, MCBs, label kit etc.)
- Carton 3 - 4000630 5kWh battery module 1
- Carton 4 - 4000630 5kWh battery module 2

11452 sonnen LCD programming tool (sold separately) required to commission on 3 phase site

Installer training (required for commissioning): https://sonnen.com.au/become-installer/

Free delivery to metropolitan areas with forklift, or discounted freight for regional areas and metropolitan areas without forklift. Contact us for a tailored freight quote.

- Works with single phase Sigenergy controllers
- Supports up to 2 Sigenergy controller connections (maximum 12kVA total)
- 12kVA smart port connection for backup generator, AC Coupled inverter or smart loads
- Rear entry knockouts included
- Cable cover included for bottom entry

Only suitable for 5kWh and 8kWh modules

Suitable for indoor & outdoor installations.
Branded, battery-specific instructions included with your install.
Comprehensive kit – includes all labels for common installation requirements. Shutdown labels – Multi-scenario and product-specific labels with images.
Includes Plaque with all labels required adjacent to the battery, to make the labelling look as professional as the install.
Waterproof safety data sheet – Comes in a magnetic holder to easily attach inside the MSB.
Clear instructions – Guidance on where to place each label for different scenarios.
Engineered in Australia – Designed in-house by our expert engineers.
Great value for money.

RPEQ-certified engineering report validating that the detailed system design complies with Energy Queensland connection standards and all relevant Australian Standards, covering inverter response modes, export limits, and protection settings. 

Note: This product is available for purchase in full pallet quantities only. Minimum order quantity (MOQ): 36 panels.

Secondary Network Protection and Solar Distribution board includes:
• Board Dimensions: 800H x 600W x 250D [mm]
• Board Colour: RAL 7035
• IP66
• Powder-coated steel with top and bottom gland plates
• Switchgear rated to 100A
• ABB Grid Protection Relay, pre-programmed to DNSP settings
• Fault rated to 25kA
• Fault current applies to entire assembly, complying with AS/NZS 61439.1:10
• For higher fault currents, please call ACSW to discuss
• Spare 3 phase MCB
• Internal RCBO protected GPO
• Separate GPR Supply and voltage reference
• Fuse protected monitoring
• 3-Point Locking System
• Pre-labelled with additional labels included for MSB
• Pre-wired and factory tested according to AS/NZS 61439.1: Clause 11
• Compliant to AS/NZS 3008.1.1:2017, AS/NZS 3000:2018, AS/NZS 5033:2021, AS/NZS 4777.1:2016, AS/NZS 61439.2:2016

- Available Modifications -
• Swap ABB Network Protection Relay for ComApp MainsPro (+$50)
• Install test links for injection testing (+$100)
• Install Generation Signalling Device (Queensland only) (+$100)
• Install 3P+N AC surge diversion (+$250)

Secondary Network Protection and Solar Distribution board includes:
• Board Dimensions: 800H x 600W x 250D [mm]
• Board Colour: RAL 7035
• IP66
• Powder-coated steel with top and bottom gland plates
• Switchgear rated to 200A
• MainsPro Grid Protection Relay, pre-programmed to DNSP settings
• Fault rated to 18kA
• Fault current applies to entire assembly, complying with AS/NZS 61439.1:10
• For higher fault currents, please call ACSW to discuss
• Spare 3 phase MCB
• Internal RCBO protected GPO
• Separate GPR Supply and voltage reference
• Fuse protected monitoring
• 3-Point Locking System
• Pre-labelled with additional labels included for MSB
• Pre-wired and factory tested according to AS/NZS 61439.1: Clause 11
• Compliant to AS/NZS 3008.1.1:2017, AS/NZS 3000:2018, AS/NZS 5033:2021, AS/NZS 4777.1:2016, AS/NZS 61439.2:2016

- Available Modifications -
• Install test links for injection testing (+$100)
• Install Generation Signalling Device (Queensland only) (+$100)
• Install 3P+N AC surge diversion (+$250)

* Inverter MCB's are not included in this board *
Please advise what inverters are being connected and we can quote these separately.

Secondary Network Protection and Solar Distribution board includes:
• Board Dimensions: 800(H) x 600(W) x 250(D) [mm]
• Board Colour: RAL 7035
• IP66
• Powder-coated steel with top and bottom gland plates
• Switchgear rated to 160A
• Mainspro Grid Protection Relay, pre-programmed to DNSP settings
• Fault rated to 18kA
• Fault current applies to entire assembly, complying with AS/NZS 61439.1:10
• For higher fault currents, please call ACSW to discuss
• Spare 3 phase MCB
• Internal RCBO protected GPO
• Separate GPR supply and voltage reference
• Fuse protected monitoring
• 3-Point Locking System
• Pre-labelled with additional labels included for MSB
• Pre-wired and factory tested according to AS/NZS 61439.1: Clause 11
• Compliant to AS/NZS 3008.1.1:2017, AS/NZS 3000:2018, AS/NZS 5033:2021, AS/NZS 4777.1:2016, AS/NZS 61439.2:2016
• Install 3P+N AC surge diversion (+$250)

- Installation of General Signalling Device (Queensland only) (+$100)

• Install 3P+N AC surge diversion (+$250)

• Install Generation Signalling Device (Queensland only) (+$100)

Secondary Network Protection and Solar Distribution board includes:
• Metal Enclosure: 800(H) x 600(W) x 250(D) [mm]
• Enclosure Colour: RAL 7035
• IP66
• Powder-coated steel with top and bottom gland plates
• Switchgear rated to 200A
• ABB Grid Protection Relay, pre-programmed to DNSP settings
• Fault current rated to 18kA
• Fault current applies to entire assembly, complying with AS/NZS 61439.1:10
• For higher fault currents, please call ACSW to discuss
• 2 Inverter circuit breakers (100A)
• Spare 3 phase MCB
• Internal RCBO protected GPO
• Separate GPR supply and voltage reference
• Fuse protected monitoring
• 3-Point Locking System
• Pre-labelled with additional labels included for MSB
• Pre-wired and factory tested according to AS/NZS 61439.1: Clause 11
• Compliant to AS/NZS 3008.1.1:2017, AS/NZS 3000:2018, AS/NZS 5033:2021, AS/NZS 4777.1:2016, AS/NZS 61439.2:2016

- Available Modifications -
• Swap ABB Network Protection Relay for ComApp MainsPro (+$50)
• Install test links for injection testing (+$100)
• Install Generation Signalling Device (Queensland only) (+$100->200)
• Install 3P+N AC surge diversion (+$250)

10kW Inverter factory locked to 5kW for CEC/DNSP requirements (becomes a 10kW inverter in backup mode)
Hybrid inverter compatible with up to 3 SolarEdge Home Batteries
SolarEdge Wireless Gateway and 70A CT included in box
SolarEdge Energy Meter and Home Network comms built-in

SolarEdge Backup Interface required for backup functionality
SolarEdge Optimisers required to connect PV

Hybrid inverter compatible with up to 3 SolarEdge Home Batteries
SolarEdge Energy Meter, 70A CT and Home Network Comms included in box

SolarEdge Backup Interface required for backup functionality
SolarEdge Optimisers required to connect PV

- Includes EYEM4 Wi-Fi dongle
- Comes with complimentary cable cover
- DTSD1352/DTSU666-20 consumption meter purchased separately
- 4 MPPT (2 strings per MPPT)
- IP66
- 645mm x 575mm x 245mm - 41kg